1000BASE-T1 MediaConverter SFP Module

← Swipe → or Click and Drag to rotate
TECHNICA ENGINEERING’S MEDIA CONVERTERS
1000BASE-T1 SFP Module
Art.-Nr.: TE-1437
Convert between 1000BASE-T1 (automotive Gigabit Ethernet) and SGMII Interface.
Order now
Description

The 1000BASE-T1 SFP Module is the cutting-edge solution to convert between 1000BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and provides an Automotive Gigabit Ethernet interface (1000 Mbit/s full-duplex, on one single twisted pair cable). An ideal candidate to interact with automotive Ethernet with gigabit interfaces in test houses. When plugged into approved devices, Hardware-in-Loop (HiL) systems and test benches with compatible chassis, the SFP Module must be configured to automotive Ethernet 1000BASE-T1 after power-up. The product features a DIP switch under the module for adjustment of Master / Slave mode of operation for automotive Ethernet 1000BASE-T1.

 

By using the Marvell 88Q2112 A2 PHY transceiver, we ensure a trustworthy and effective tool to our customers that are looking for a cost-efficient, quick and manageable solution for their testing requirements, with minimum latency and maximum reliability. Registers of the integrated transceiver are accessible via I2C interface for diagnosis and reconfiguration.

 

No customized driver is needed to interact with this device once it has been properly initialized. It communicates with the SGMII interface. It is equipped with a Molex connector which suits to the small available size. The metal housing makes it robust with IP20 protection. The device is capable to function in a variating temperature range from 0 Celsius to +70 Celsius. With the in-built status LED, the operation of the device is transparent and aids the tester to detect Link up and data transmission visually.

 

The device can be used with our MediaGateway and other approved chassis of Technica partners. However, the SFP Modules do not work in a “plug-and-play” manner with any SFP-capable system. In order to set-up the SFP Modules to work in your system, you must be able to interact via I²C and get in touch with Marvell (the PHY manufacturer) to receive the NDA protected PHY-register setting datasheet in order to initialize the phy properly. In this regard, Technica cannot support, due to NDA restrictions. Some commercially available devices might successfully recognize and work with the SFP Module, this cannot be guaranteed by Technica.

 

Thus, the 1000BASE-T1 SFP is the ideal solution for working quickly and efficiently with the new gigabit technology without the hustle of extra- wiring, customized connectors, and vendor specific tools.

 

Features
  • 1000BASE-T1 and SGMII converter
  • Marvell 88Q2112 A2 PHY (“IEEE” or “Legacy” can be set in phy register settings, see User Manual)
  • Fits into a standard SFP slot
  • Power requirements: 3.3 Volt DC
  • Supports I2C for internal register access
  • Status LEDs
  • Master/Slave either via small DIP switch or PHY register settings
  • Size: 68 x 14 x 14 mm

Downloads

More Information below

Downloads

1000BASE-T1 SFP Module - Flyer (PDF)
1000BASE-T1 SFP Module - User Manual v2.6
1000BASE-T1 SFP Module - Cable set v1.0
1000BASE-T1 SFP Module -EU Declaration of conformity

Support

Do you need any assistance?

If you need any help regarding the selection of a product, please send us an E-mail here.
E-Mail
If you have already acquired products from Technica Engineering and need assistance, please click here.
Support
TECHNICA ENGINEERING’S MEDIA CONVERTERS
1000BASE-T1 SFP Module
Art.-Nr.: TE-1437

    Please enter your contact information below. We will be in touch with you shortly.

    GUIDELINE FOR THE EXECUTION OF RETURN OF PRODUCTS-CASES

    Dear business partner,
    please take note of the following, which enable us to handle products that you would like to return as promptly and as efficiently as possible.

    If you have general support questions about our products, please refer to us via Email to support@technica-engineering.de

    Return Procedure

    1. For the return of products this form is necessary.
    2. Please fill the form thoroughly.
    3. Please, print the form and enclose it to your consignment.
    4. Following this, please send your parcel within 5 business days to:

    Technica Engineering GmbH
    TE-Logistics
    Carl-von-Linde Strasse 15
    85748 Garching b. München
    GERMANY

    To ensure promt processing, please make sure to always enclose your form. We might be unable to process and have to return your consignment to you if we received it without the according return of product form.

    RMA execution internally (only for packages with RMA form)

    1. The processing time after arrival is 14 business days.
    2. After the processing time and within the warranty of 6 months, there will be an immediate replacement (new goods) if the goods are in stock.
    3. Tracking is sent to the customer by email.