1000BASE-T1 MediaConverter EMC

← Swipe → or Click and Drag to rotate
MediaConverter
1000BASE-T1 EMC
Art.-Nr.: TE-1400-1
The ideal solution for working quickly & efficiently with 100/1000BASE-T1 EMC measurements
Order now
Description

The 1000BASE-T1 MediaConverter EMC establishes one direct point-to-point conversion between automotive ECUs using 1000BASE-T1 (1000 Mbit/s, Fullduplex, with 1x Shielded or Unshielded Twisted Pair cable) and any Standard Gigabit Ethernet (1 Gbit/s, 1000BASE-T) device with an RJ-45 connector. In the conversion, no packets are stored or modified. The conversion takes place on a Physical Layer with the highest proven reliability.

 

By using the Marvell 88Q2112 A2 PHY, we ensure a trustworthy and effective tool to our customers that are looking for a cost-efficient, quick, and manageable solution for their testing requirements, with no latency and no packet loss. Via DIP Switch, the Marvell 88Q2112 A2 Phy can be used in “IEEE” or in “Legacy” mode.

 

The device features bi-directional conversion between Standard Gigabit Ethernet (1000BASE-T) and Automotive Gigabit Ethernet (1000BASE-T1). A massive stainless-steel housing, coupled with DIP switches for ease of configuration enables the user to interact with the converter, effortlessly.

 

Our 1000BASE-T1 EMC MediaConverter can work both in 1000BASE-T1 mode, as well as in 100BASE-T1 mode when used with our MediaGateway outside the chamber (optical SFP on the MG)). The use case with the MediaGateway can be seen in the photo “Use Case 1400-2 A” above.

 

No customized driver is needed to interact with our 1000BASE-T1 MediaConverter. The device communicates with standard Ethernet through an SFP (small form-factor pluggable) interface. It comes with an automotive grade MQS connector (Power),  an automotive approved MATEnet connector for 1000BASE-T1, and a standard SFP (small form-factor pluggable) slot. Its design makes it portable and easy to install in test racks and the included optical SFPs with LC/LC optical fiber makes its use inside EMC chambers possible. The stainless-steel housing makes it robust with IP20 protection and improves the EMC performance. The device is capable to function in a variating temperature range from -40 Celsius to +80 Celsius. With the in-built status LEDs, the operation of the device is transparent and aids the tester to detect Link up and data transmission visually.

The additional optical interface with ST/ST connectors provides additional insight to phy-internal information via the included USB adapter board.

No extra hardware or software is needed to connect the device with a PC or a Laptop. The device can be coupled with any hardware or software tool that runs on standard gigabit Ethernet with an RJ-45 connector. Thus, the 1000BASE-T1 MediaConverter is the ideal solution for working quickly and efficiently with the new 1000BASE-T1 technology without the hustle of extra- wiring, customized connectors, and vendor-specific tools.

 

Features
  • Converts Automotive Gigabit Ethernet: 1000BASE-T1 (1000 MBit/s full duplex, 1x single twisted pair (STP)) to Standard Gigabit Ethernet (SFP)
  • Master/slave configuration
  • SFP Module allows optical Ethernet connection or standard Gigabit Ethernet through RJ45 Connector
  • Allows to perform EMC test through the optical interface
  • Status LEDs
  • Configuration DIP switches
  • Automotive MateNET connector and cables included (Power, 1000BASE-T1)
  • Stainless steel housing
  • Size: 95 x 95 x 32mm

DOWNLOADS

FURTHER INFORMATION BELOW

Downloads

1000BASE-T1 MediaConverter EMC - Flyer (PDF)
1000BASE-T1 MediaConverter EMC - EU Declaration of conformity

Support

Do you need any assistance?

If you need any help regarding the selection of a product, please send us an E-mail here.
E-Mail
If you have already acquired products from Technica Engineering and need assistance, please click here.
Support
MediaConverter
1000BASE-T1 EMC
Art.-Nr.: TE-1400-1

    Please enter your contact information below. We will be in touch with you shortly.

    GUIDELINE FOR THE EXECUTION OF RETURN OF PRODUCTS-CASES

    Dear business partner,
    please take note of the following, which enable us to handle products that you would like to return as promptly and as efficiently as possible.

    If you have general support questions about our products, please refer to us via Email to support@technica-engineering.de

    Return Procedure

    1. For the return of products this form is necessary.
    2. Please fill the form thoroughly.
    3. Please, print the form and enclose it to your consignment.
    4. Following this, please send your parcel within 5 business days to:

    Technica Engineering GmbH
    TE-Logistics
    Carl-von-Linde Strasse 15
    85748 Garching b. München
    GERMANY

    To ensure promt processing, please make sure to always enclose your form. We might be unable to process and have to return your consignment to you if we received it without the according return of product form.

    RMA execution internally (only for packages with RMA form)

    1. The processing time after arrival is 14 business days.
    2. After the processing time and within the warranty of 6 months, there will be an immediate replacement (new goods) if the goods are in stock.
    3. Tracking is sent to the customer by email.